How to Apply GHOSTBOND: A Step-by-Step Guide for Hair Systems
GHOSTBOND gives a secure, natural-looking bond on lace and poly hair systems, but how long it holds depends as much on how you apply it as on which adhesive you choose. This step-by-step guide covers how to apply GHOSTBOND, from preparing your scalp to pressing the system into place, plus the most common mistakes that shorten the hold.
Hair4All is an official GHOSTBOND UK stockist and an Authorised and Approved distributor of GHOSTBOND. These are the steps we follow when bonding systems at our Bristol studio.
What you will need
- Your GHOSTBOND adhesive: Classic, Endure, Sport, Motion or Daily
- GHOSTBOND Scalp Protector to prepare the skin
- A small brush or applicator
- A hairdryer on a cool setting, if you want to speed up drying
- A remover such as GHOSTBOND BondBreak for tidying up and for the next takedown
Choose the right GHOSTBOND first
Each GHOSTBOND adhesive is made for a different routine. Classic is a dependable everyday hold for oily scalps. Endure is built for multi-week wear in heat, humidity and cold. Sport resists sweat and scalp oils and is GHOSTBOND's strongest hold. Motion has a matte, no-shine finish for the camera. Daily uses Peelable Tech for wearers who remove and reapply often. If you are not sure, try the GHOSTBOND Adhesive Finder.
Step 1: Prepare the scalp and the system
Clean the bonding area thoroughly to remove oil, sweat and old adhesive, then make sure the skin is completely dry. Clean and dry the base of the hair system as well. Any oil or moisture left on the skin will weaken the bond, so avoid moisturisers and oily products on the bonding area beforehand.
If your scalp tends to be oily, GHOSTBOND Clarifying Shampoo gives a deeper cleanse before a new application, and Smooth Start Exfoliating Gel exfoliates the scalp during preparation.
Step 2: Apply Scalp Protector
GHOSTBOND Scalp Protector preps the skin before adhesive. Apply it to the bonding area and let it dry fully before you start on the adhesive. If you sweat heavily, GHOSTBOND No Sweat Scalp Spray leaves the scalp feeling dry and fresh before adhesive is applied.
Step 3: Apply thin, even layers of GHOSTBOND
Brush a thin, even layer of GHOSTBOND onto the bonding area of the skin and, where your system's base calls for it, onto the base too. GHOSTBOND goes on milky white and dries clear. Let each layer turn completely clear and tacky before adding the next. Most wearers use three to five thin layers.
A cool hairdryer can speed up drying, but do not rush it. Thick layers, or layers applied before the one underneath has turned clear, are the most common reason a bond fails early.
Step 4: Position and press
Once the final layer is clear and tacky, position the system carefully, starting at the front hairline. Press it firmly into place, working out towards the edges, and pay particular attention to the hairline and perimeter, where lifting usually starts. Avoid disturbing the bond for the first few minutes while it sets, then press the edges down again.
Step 5: Look after the bond
Oily skin, exercise, heat and humidity all shorten the hold. For a longer hold, match the adhesive to your routine, keep the edges clean, and wash the hair on your system with a gentle product such as GHOSTBOND Daily Refresh Shampoo. Our guide to how long GHOSTBOND lasts covers the factors in more detail.
Common mistakes to avoid
- Applying to damp or oily skin. The skin must be clean and completely dry.
- Thick layers. Several thin layers hold far better than one or two heavy ones.
- Not waiting for each layer to turn clear. Adding a layer while the one beneath is still white traps moisture and weakens the bond.
- Using the wrong adhesive for your routine. If you sweat heavily or train often, Sport is built for that; for long wear in any climate, choose Endure.
- Skipping the patch test. If you have sensitive skin, patch test any new adhesive before the first full application.
Removing GHOSTBOND
When it is time for a takedown, never pull the system off. Apply GHOSTBOND BondBreak along the bonded area and give it time to work before lifting gently, then clean the base with GHOSTBOND BondGone. Our guide to the GHOSTBOND removal and care routine covers each step.
Buy genuine GHOSTBOND
Hair4All is an official GHOSTBOND UK stockist, and every bottle comes directly from Professional Hair Labs. Orders placed before 2pm, Monday to Friday, are dispatched the same day, and UK delivery is free on orders over £50. Shop GHOSTBOND UK.



